Gpsmapedit 1.0.66.7 crack. Cisco ASA 5500 Series Configuration Guide using the CLI, 8.2. Chapter Title. Step 1 Obtain the serial number for your ASA by entering the following command. Hostname# show activation-key Step 2 If you are not already registered with Cisco.com, create an account. ![]() Management Access This chapter describes how to access the Cisco ASA for system management through Telnet, SSH, and HTTPS (using ASDM), how to authenticate and authorize users, and how to create login banners. • • • • Configure Management Remote Access This section describes how to configure ASA access for ASDM, Telnet, or SSH, and other management parameters such as a login banner. • • • • • • • • Configure ASA Access for ASDM, Telnet, or SSH This section describes how to configure ASA access for ASDM, Telnet, or SSH. See the following guidelines: • To access the ASA interface for management access, you do not also need an access rule allowing the host IP address. You only need to configure management access according to the sections in this chapter. If, however, you configure HTTP redirect to redirect HTTP connections to HTTPS automatically, you must enable an access rule to allow HTTP; otherwise, the interface cannot listen to the HTTP port. • Management access to an interface other than the one from which you entered the ASA is not supported. For example, if your management host is located on the outside interface, you can only initiate a management connection directly to the outside interface. The only exception to this rule is through a VPN connection. ![]() • The ASA allows: • A maximum of 5 concurrent Telnet connections per context, if available, with a maximum of 100 connections divided among all contexts. • A maximum of 5 concurrent SSH connections per context, if available, with a maximum of 100 connections divided among all contexts. • A maximum of 5 concurrent ASDM instances per context, if available, with a maximum of 32 ASDM instances among all contexts. • You cannot use Telnet to the lowest security interface unless you use Telnet inside a VPN tunnel. • (8.4 and later) The SSH default username is no longer supported. You can no longer connect to the ASA using SSH with the pix or asa username and the login password. To use SSH, you must configure AAA authentication by choosing Configuration > Device Management > Users/AAA > AAA Access > Authentication; then define a local user by choosing Configuration > Device Management > Users/AAA. If you want to use a AAA server for authentication instead of the local database, we recommend also configuring local authentication as a backup method. Before you begin • In multiple context mode, complete this procedure in the context execution space. To change from the system to a context configuration, in the Configuration > Device List pane, double-click the context name under the active device IP address. • To gain access to the ASA CLI using Telnet, enter the login password. You must manually set the password before using Telnet. Procedure Step 1 Choose Configuration > Device Management > Management Access > ASDM/HTTPS/Telnet/SSH, and click Add. The Add Device Access Configuration dialog box appears. Step 2 Choose the type of session from the three options listed: ASDM/HTTPS, Telnet, or SSH. Step 3 Choose the management interface and set the host IP addresses allowed, and click OK. Specify any named interface. For bridge groups, specify the bridge group member interface. For VPN management access only (see ), specify the named BVI interface. Step 4 To require certificate authentication, in the Specify the interface requires client certificate to access ASDM area, click Add to specify the interface and an optional certificate map that must be matched for successful authentication. See Configuration > Remote Access VPN > Network (Client) Access > Advanced > IPSec > Certificate to Connection Map > Rules to create the certificate map. For more information, see. Step 5 Configure HTTP Settings. • Make sure the Enable HTTP Server check box is checked. This is enabled by default. • Change the Port Number, Idle Timeout, and Session Timeout as desired. Step 6 (Optional) Configure Telnet settings. The default timeout value is 5 minutes. Step 7 (Optional) Configure SSH settings. For DH Key Exchange, click the applicable radio button to choose Diffie-Hellman (DH) Key Exchange Group 1 or Group 14. Both the DH Group 1 and Group 14 key-exchange methods for key exchange are supported on the ASA. If no DH group key-exchange method is specified, the DH group 1 key-exchange method is used.
0 Comments
Leave a Reply. |